Introduction to Application Methods for Thin-Film Fire-Retardant Coatings
Release date:
2022-12-07
Author:
Zhengxiang Fireproof Materials
Thin-type fireproof coatings are water-based fireproof coatings for steel structures. They refer to coatings with a thickness greater than 3 mm and less than or equal to 7 mm, which provide a certain decorative effect. At high temperatures, they expand and thicken, offering a fire resistance rating of up to 2 hours. These coatings typically consist of suitable water-based polymers as the base material, flame-retardant composite systems, flame retardant additives, and refractory fibers. Their fire-protection mechanism is the same as that of ultra-thin types.
Thin-type fireproof coating is a water-based fireproof coating for steel structures. Thin-type fireproof coating This refers to fire‑protective coatings for steel structures with a coating thickness greater than 3 mm and not exceeding 7 mm, offering a certain decorative effect. These coatings expand and thicken at high temperatures and provide a fire resistance rating of up to 2 hours. They typically consist of suitable water‑based polymers as the binder, a flame‑retardant composite system, flame‑retardant additives, and refractory fibers. Their fire‑protection mechanism is similar to that of ultra‑thin intumescent coatings. For this type of coating, the selected water‑based polymer must exhibit excellent adhesion to steel substrates, durability, and water resistance. Its decorative appearance is superior to that of thick‑type fireproofing coatings, and its fire resistance rating generally does not exceed 2 hours. Consequently, in steel structure fire‑protection projects requiring a fire resistance rating of less than 2 hours, spray application is commonly employed.
What is the fire‑resistant and heat‑insulating principle of thin‑type fireproof coatings? Let’s analyze it below.
The fire‑protective and insulating principle of thin‑film intumescent coatings applied to steel structures is that, when exposed to fire, the coating expands and forms a foam layer. This foam not only blocks oxygen but also, due to its porous structure, provides excellent thermal insulation, thereby slowing the rate at which heat is transferred to the underlying substrate. Based on physicochemical principles, the expansion and foaming process generates an endothermic reaction as the coating volume increases, while simultaneously consuming heat released during combustion, thus helping to lower the system temperature. These mechanisms enable intumescent coatings to deliver significant fire‑protective and insulating performance.
Thin-type fireproof coating What is the construction method? Let’s analyze it below.
1. Clean dust and oil from the steel surface.
2. Inspect the steel structure surface for any areas with missed coats; if found, apply a touch-up coat first. Once it is confirmed that no areas have been missed, proceed with the application of the thin‑film steel fire‑proof coating NB (BT-02). To improve work efficiency, spray application is recommended.
3. Before spraying, mix the material thoroughly with a handheld mixer. If it is too thick, you can add a small amount of water—no more than 5% of the coating volume; do not use excess water, as this will reduce adhesion.
4. The thoroughly mixed thin‑type fire‑resistant coating is applied using a spray gun, held no more than 35 cm from the surface. Compressed air pressure must exceed 0.5 MPa. The coating thickness depends on the required fire‑resistance rating. Allow sufficient time between coats for the previous layer to become non‑sticky; proceed with the next coat only after it has dried to the touch.
5. Operating conditions: in the absence of rain, wind force must be at level 4 or below, and wind protection measures must be in place; otherwise, a significant amount of thin-film steel structure fireproof coating will be wasted.
Thin-type fireproof coating What are its advantages? Let’s analyze them below.
1. The thin fireproof coating is lightweight, with a dry density of approximately 0.61/m3;
2. Contains no asbestos or organic solvents; it is harmless to humans and non-corrosive.
3. Thin-type steel structure fireproof coating has strong adhesion, does not require wire mesh reinforcement, and will not naturally fall off;
4. Good seismic, flexural, and freeze–thaw resistance.
Tag
Recommended Information
Contact Us
WhatsApp:
Phone:
Email:
Address:
Northwest corner of the intersection of Fengya Avenue and Shaoze Road, Xinxing Industrial Park, Jize County, Handan City, Hebei Province